96 lines
3.7 KiB
C++
96 lines
3.7 KiB
C++
/*******************************************************************************
|
|
* Copyright 2016 ROBOTIS CO., LTD.
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
* you may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*******************************************************************************/
|
|
|
|
#include <Dynamixel2Arduino.h>
|
|
|
|
// Please modify it to suit your hardware.
|
|
#if defined(ARDUINO_AVR_UNO) || defined(ARDUINO_AVR_MEGA2560) // When using DynamixelShield
|
|
#include <SoftwareSerial.h>
|
|
SoftwareSerial soft_serial(7, 8); // DYNAMIXELShield UART RX/TX
|
|
#define DXL_SERIAL Serial
|
|
#define DEBUG_SERIAL soft_serial
|
|
const uint8_t DXL_DIR_PIN = 2; // DYNAMIXEL Shield DIR PIN
|
|
#elif defined(ARDUINO_SAM_DUE) // When using DynamixelShield
|
|
#define DXL_SERIAL Serial
|
|
#define DEBUG_SERIAL SerialUSB
|
|
const uint8_t DXL_DIR_PIN = 2; // DYNAMIXEL Shield DIR PIN
|
|
#elif defined(ARDUINO_SAM_ZERO) // When using DynamixelShield
|
|
#define DXL_SERIAL Serial1
|
|
#define DEBUG_SERIAL SerialUSB
|
|
const uint8_t DXL_DIR_PIN = 2; // DYNAMIXEL Shield DIR PIN
|
|
#elif defined(ARDUINO_OpenCM904) // When using official ROBOTIS board with DXL circuit.
|
|
#define DXL_SERIAL Serial3 //OpenCM9.04 EXP Board's DXL port Serial. (Serial1 for the DXL port on the OpenCM 9.04 board)
|
|
#define DEBUG_SERIAL Serial
|
|
const uint8_t DXL_DIR_PIN = 22; //OpenCM9.04 EXP Board's DIR PIN. (28 for the DXL port on the OpenCM 9.04 board)
|
|
#elif defined(ARDUINO_OpenCR) // When using official ROBOTIS board with DXL circuit.
|
|
// For OpenCR, there is a DXL Power Enable pin, so you must initialize and control it.
|
|
// Reference link : https://github.com/ROBOTIS-GIT/OpenCR/blob/master/arduino/opencr_arduino/opencr/libraries/DynamixelSDK/src/dynamixel_sdk/port_handler_arduino.cpp#L78
|
|
#define DXL_SERIAL Serial3
|
|
#define DEBUG_SERIAL Serial
|
|
const uint8_t DXL_DIR_PIN = 84; // OpenCR Board's DIR PIN.
|
|
#else // Other boards when using DynamixelShield
|
|
#define DXL_SERIAL Serial1
|
|
#define DEBUG_SERIAL Serial
|
|
const uint8_t DXL_DIR_PIN = 2; // DYNAMIXEL Shield DIR PIN
|
|
#endif
|
|
|
|
#define TIMEOUT 10 //default communication timeout 10ms
|
|
const uint8_t DXL_ID = 1;
|
|
const float DXL_PROTOCOL_VERSION = 2.0;
|
|
uint8_t option = 0;
|
|
|
|
Dynamixel2Arduino dxl(DXL_SERIAL, DXL_DIR_PIN);
|
|
|
|
void setup() {
|
|
// put your setup code here, to run once:
|
|
|
|
// Use UART port of DYNAMIXEL Shield to debug.
|
|
DEBUG_SERIAL.begin(115200); //Set debugging port baudrate to 115200bps
|
|
while(!DEBUG_SERIAL); //Wait until the serial port for terminal is opened
|
|
|
|
// Set Port baudrate to 57600bps. This has to match with DYNAMIXEL baudrate.
|
|
dxl.begin(57600);
|
|
// Set Port Protocol Version. This has to match with DYNAMIXEL protocol version.
|
|
dxl.setPortProtocolVersion(DXL_PROTOCOL_VERSION);
|
|
}
|
|
|
|
void loop() {
|
|
// put your main code here, to run repeatedly:
|
|
|
|
bool ret = false;
|
|
DEBUG_SERIAL.println();
|
|
DEBUG_SERIAL.println("Reboot DYNAMIXEL? [y/n]");
|
|
|
|
DEBUG_SERIAL.read();
|
|
while(DEBUG_SERIAL.available()==0);
|
|
option = DEBUG_SERIAL.read();
|
|
|
|
switch(option) {
|
|
case 'y':
|
|
case 'Y':
|
|
ret = dxl.reboot(DXL_ID, TIMEOUT);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
if(ret) {
|
|
DEBUG_SERIAL.println("Reboot Succeeded!");
|
|
} else {
|
|
DEBUG_SERIAL.println("Reboot Failed!");
|
|
}
|
|
|
|
delay(1000);
|
|
} |